Building the Big Bertha - Part 3 (For N00bs)

[Click here for Part 1]

Now that your fins have dried, it's time to sand them smooth.

They'll be pretty rough when you start. The CWF will have formed ridges and clumps, and you need to knock all that off before you get to the finer sanding.

A fin from my Crossfire ISX - again, I neglected to take
pictures of the Big Bertha fins here. See how rough the
fin looks? You need to sand off those brush marks.

Use a sanding block (this can be a scrap of wood with sandpaper wrapped tightly around it) and a rougher grit of sandpaper - say, 220. Sand in little circles until most of the brush marks are nearly gone, then switch to a finer grit of paper - 320 or 400. Continue sanding in little circles.

Now, when I started doing this, I assumed you sand until all the CWF is gone, and the balsa grain would be filled. CWF is good, but not that good. If you sand off all the CWF, you're going to see wood grain in your paint job. So, what you want to do is sand most of the wood filler off and leave just a thin layer or skin of it.

You'll likely expose a bit of wood. This is fine for now. Just go slowly and be careful. I find that the edges of the fins have exposed wood while the center is still coated in CWF. This is probably due to either a very slight warp in the fins, or not having the sandpaper tightly enough against the sanding block, or possibly pressing too hard toward the outside. Either way, it's kind of unavoidable sometimes. We're going to repeat this process, so don't sweat it.

Sand the edges carefully, finding that rounded edge without overdoing it and sanding any of the wood off. Sand the root edge if you have any CWF on it, and make sure it's flat. I stand my fins on the root edge to make sure they're square.

Blow away any dust from the sanding so you can see what you're doing. When you're done, most of the fins will be incredibly smooth - with some imperfections...

As I was doing my initial sanding, I accidentally gouged one side of the fin. I was sanding on a piece of newspaper that had some bits of stuff underneath, and pressing down made these indentations. Also, you might be able to see at the edge some exposed wood.

Gouges are what CWF was made for. I needed to recoat the fins anyway, so I made sure to use a putty knife to really push the CWF into the indentations. Do another coat of CWF, let dry, and sand again. Then do it again. About three coats should really do it, unless you get lucky with your second coat. You can thin the CWF out a little bit more on your third coat, so you use less and have less to sand off.

When you're satisfied, you're done. Wipe off any dust from the fins with a slightly damp paper towel, and dry them immediately. Set the fins aside for now.

Now, let's turn to the motor mount, or engine mount. In most rocket kits, this is a short tube which is narrower than the body of the rocket, and is held in place with a couple of rings of cardboard or round paper, called centering rings. Some rockets have no mount, as the body is the same size as the motor used, so the motor goes right into the body of the rocket. This is called a minimum-diameter rocket, as the rocket is no fatter than it needs to be to accommodate the motor. This is what you use for rockets that go high and fast, as the weight is kept to a minimum.

The Estes Hi Flier is a minimum-diameter rocket. The
body tube is the motor mount! That stand is actually
a standard motor - just the right size to fit the body.

 The Big Bertha, however, is a large, slow lifting rocket, which I like, because it doesn't disappear into the sky in a second.

The motor mount usually also has a metal hook attached to it, called an engine hook. This keeps the motor in the rocket. Inside the motor mount, you also usually have something called an engine block or thrust ring. This is just a ring of paper which keeps the motor from shooting out through the top of the rocket, destroying everything in its path.

Motor mount parts - 1) Motor tube 2) Centering rings 3) Engine hook
4) Mylar hook sleeve 5) Engine block/thrust ring

 A lot of motor mounts are built the same way. The instructions with your kit will give the proper measurements, but there's not much variation. First, you mark where the engine hook and centering rings will go. Then you cut a tiny slit for the end of the hook - this is in the fore end or top of the mount, maybe a half inch from the front end. Insert the hook, then slide the little Mylar ring over the hook and glue it in place about halfway down the length of the hook. Put some glue inside the tube just above the little tab of the engine hook and glue the engine block in place - if it's not right inside the tube, you can use a motor to push it into place, or some kits come with a cardboard tube for this purpose.

These marks, from top to bottom, are where
the engine hook will be inserted, where the
hook sleeve will go, and where the aft centering
ring will be glued. I tend to mark the fore
and aft ends of the motor tube so as not to
make a dumb mistake.

1/8 inch slit for the motor hook

Mylar hook sleeve glued in place. Don't glue
down the aft end of the hook - you need it
to bend to insert a motor!

 One centering ring has a notch in it. This is to give the hook a little flex room. That goes at the base or aft of the mount. The other ring goes at the top or fore, and butts up against the part of the engine hook sticking out of the motor tube.

These have to be well-glued. Make sure they'll fit before you glue them, sanding them a bit if they're too tight. Then apply a liberal amount of wood glue around the tube where they'll go and slide them into place. There should be enough glue to make a fillet - extra glue at the joint - to reinforce the bond.

Engine mount finished, waiting for glue to dry. You can
see the engine hook, the centering rings, the Mylar
hook sleeve, and glue fillets at the joints. The engine
block/thrust ring is inside, toward the base in this photo.

That's it. The motor mount is finished. Once it's dry, you can glue it into the base of the rocket.

Apply a good amount of wood glue about 1 1/2 - 2 inches into the base of the rocket. You need a ring of it, and you want to be kind of liberal with it. First, you want to push the glue into place, and you want it to form a reinforcing fillet of glue when it comes to rest. Second, if you use too little glue, the glue can seize up, and the motor mount can get stuck only halfway into the rocket!

You can apply the glue with a small dowel rod or craft (popsicle) stick, but I have gotten to where I just use my fingers. I can feel that I've gotten enough glue in, and I'm less likely to get glue where I don't want it if I go by feel rather than using a stick.

Push the motor mount halfway in, and apply some more glue about a quarter inch inside the base of the rocket. Push the motor mount into place, with the motor tube either flush with the base of the body tube, or with about a quarter inch of overhang (depending on your kit's instructions).

Installing a motor mount - in this case, in my Cosmic Explorer. Again, I didn't
photograph this part of the Big Bertha build...

Dribble a little wood glue between the motor tube and the body tube to get a good fillet between the aft centering ring and the body of the rocket. Use a thin dowel rod or coffee stir stick to smooth a nice fillet joint between these to parts all the way around.

Stand the rocket body tube on the fore or top end and allow all the glue to dry for at least a couple hours. I leave it overnight.

In the next post, we'll actually have (gasp!) pictures of the Big Bertha build. And we'll learn some Rocket Pro Tips on getting a good surface for painting. We're getting closer to finishing this thing!

[Click here for Part 4]

Oh, Noes!

My brakes went out when I was leaving for work this morning. I recently got my car worked on after letting it sit for about ten months, and it was so nice to be able to drive places again.

The reason I mention this here is that one of the first things I thought was Dammit! I was going to go launch rockets today!

My first couple of rocket launches with Chad were back when I was walking everywhere.  I live on the east side of Bloomington, and we launch in a huge park on the west side. Maybe it seems silly, but once I had my car back, the most satisfying part was that I could drive myself to launches, and to the huge hardware store and Michael's Crafts across town to buy building supplies.

And the weather has been so great this week! Today would have been my first time launching in weather that wasn't sweltering and humid.

I hate hot weather, especially humid weather. September and October are the perfect months for me in the Midwest. This indicates how awesome launching rockets is - I'm willing to slather on sunscreen and stand out in humid, 90-degree weather just to watch them go up.

I've gotten used to walking everywhere over the last year - I didn't even mind the polar vortex, because I bundled up tight, popped in the earbuds, and listened to podcasts during the 40-minute, 4:30 a.m. walk to work five days a week.

But this... This is a bummer.

I'm nearly finished painting and building my two most recent rockets - the Estes Cosmic Explorer and Estes Hi Flier.

Cosmic Explorer - a sleek-looking rocket that stands two feet tall

Hi Flier - 12 inch rocket which goes up to 1,500 feet

I just need to do some sanding on the paint job of the Hi Flier to knock down some tape dams - raised areas of paint caused by masking tape - and do topcoats and decals for the Cosmic Explorer, and I'm done. I've been working on these rockets for three weeks now, carefully trying to get details right, fill wood grain properly, and fixing a few things I messed up. I'm still working on the details of making a rocket look as good as it can.

But this workday - and the walk home - were so long, I might have to lie down before doing any sanding or painting. I want to get right to work on these, but I think I get sloppy when I'm too tired. I'm working on being patient to get the best results.

Just a couple previews:

I've opted for my own color scheme for the Hi Flier - blue and gold. Chad has one in the traditional color scheme (actually, had. He lost that one.), and as I've said before, when he already has a rocket, if I get the same one, I like to make mine look different. I thought of the Blue Angels when I was coming up with ideas:

But I'll probably skip the sticker. I am not a huge fan of self-adhesive stickers, and I usually get them on crooked, and there they stay.

And I've managed to put a pretty decent airfoil on the fins of the Cosmic Explorer:

This would have been easier to see if I'd taken a closeup later, after priming
the rocket. I'll post pictures of the whole thing when I'm done.

OK. Time to nap, sand, and paint...